What temperature is the tool holder heated to during the shrinking process?

This depends on the geometry of the holder, the size of the clamping diameter and the taper size. While some standard holders have 4.5 degrees, slim holders have 3 degrees. Depending on the type, a different temperature from 150˚C to 350˚C is used when shrinking the holder.

The fume extraction system reliably removes fumes from the operator's working area. The established and patented fume extraction system above the induction coil has been extended to include an integrated extraction system inside the coil housing. The fumes are therefore extracted directly where they are produced. The filter unit has a safe place in the under-table.

What types of cutting materials can be used in shrink-fit holders for the shrink-fit process?

Steel, HSS, carbide, heavy metals, metal powder, shrink-fit extensions.

What is the required tolerance for the shank diameter of the cutting tool when using a shrink-fit tool holder?

The shank tolerance of the cutting tool must be h6 or h5.

Is it possible to monitor the service life of the tool holder and the number of shrink cycles of the tool holder?

With the ZOLLER »powerShrink« it is possible to monitor the heating cycles of the tool holder using a unique tool holder ID number, e.g. the ZOLLER »idChip« technology. Each cycle is monitored and registered in the »pilot« software.

What is the minimum and maximum heating time?

The heating time depends on the geometry of the tool holder and the clamping diameter. For small diameters, this takes 2 to 3 seconds, for large diameters 5 to 7 seconds.

What is the minimum and maximum cooling time?

ZOLLER offers two types of cooling systems: A non-contact cooling system with air cooling and cooling adapters. Depending on the tool diameter, the cooling time with cooling adapters is 60 to 120 seconds. With »Zstream« air cooling, the process is called conditioning, in which the entire tool holder is cooled from the nose to the flange. The conditioning time here depends on the diameter of the holder and is 3 to 5 minutes.

Is an air-conditioned room required to install the »powerShrink« device?

An air-conditioned room is not required. The device can be installed in a dust-free area in the machine hall.

How does shrinking work and what kind of process takes place here?

The concept is simple. Each shrink tool holder is manufactured with an internal diameter that is slightly smaller than the shank diameter of the cutting tool. Using an induction device, the nose area of the tool holder is quickly heated to increase the internal diameter. At this point, the cutting tool can be inserted into the tool holder. The tool holder is then cooled and the diameter shrinks, exerting a force on the shank of the cutting tool to hold it precisely in position.

What is non-contact cooling and contact cooling?

When tool holders are shrunk without direct contact, the tool holder system is called non-contact cooling. This is done, for example, with the help of cooling adapters or air cooling. If the tool holders are cooled with a liquid after heating, this process is called quenching. The service life of the holder is reduced and the holder rusts if the tool holder continues to be used with liquids directly on it. The cooling liquid becomes dirty after a short time and must be replaced, otherwise it collapses, smells strongly and contains harmful ingredients that are dangerous to human skin.

Is it possible to use the same shrink-fit machine for standard diameters from 3 to 32 mm and heavy-duty shrink-fit holders for diameters over 32 mm?

Yes, this is possible with the ZOLLER »powerShrink 600«, where the 14 kVA induction coil and the 22 kVA induction coil can be exchanged quickly and easily via the quick-change interface.

Is it possible to adjust the overall length of the tool after shrinking with the »powerShrink« machine?

Yes, with the »eQset« and »liteSet« adjustment systems it is possible to preset the overall length of the tool on the »powerShrink«.

Air cooling »zStream«

With ZOLLER's air cooling »zStream« you obtain maximal flexibility and protection with the cooling of your shrink fit tool holder, independently of its contour or diameter. In addition, your shrink-clamping tools are cooled consistently and safely across their entire length – without the risk of being damaged. »zStream« is also ideally suited for cooling placed down tools.

Length adjustment »eQset«

The integrated length adjustment system is used to set the overall length or projection length and for tool replacement. The pneumatically activated quick adjustment and fine adjustment by handwheel enable fast, ergonomic and precise positioning of the probe head to the desired height.

Scan function incl. hand scanner

The »pilot« software scan function in combination with the hand scanner enables reliable selection of the appropriate shrink fit parameter by scanning the holder number on the shrink fit holder. Regardless of the manufacturer, all shrink fit toolholders with DataMatrix code (e.g. ZOLLER »idLabel«, ZOLLER »idChip«) are supported. In the »pilot« software, each heating process can be counted for each shrink fit chuck. In addition, a warning and wear limit can be stored in relation to the permitted heating processes.

Set-up table for »powerShrink 400«

As an alternative to installation on a workbench, the »powerShrink 300« and »powerShrink 400« can be positioned on a set-up table with ergonomically optimal working height. This provides a tidy place for the cooler and flue gas suction device. The table is optionally available with sturdy rollers and an ergonomic handle to allow variable positioning.

Configurations for »powerShrink 400 | 11«

There are 3 basic configurations for the induction coils to choose from: 1. combination of any 14 kVA induction coil with quick-change interface, changing the induction coil from one induction coil axis to the other depending on the shrink chuck length 2. combination of any 2 14 kVA induction coils without »shrinkbyLight« and without quick-change interface 3. combination of any 14 kVA induction coil with a 22 kVA induction coil with quick-change interface

With your »powerShrink«, you will receive a receiving pot as standard. Additional pots can be ordered for parallel heating and cooling. The work surface is perfectly matched to the receiving pot and ensures convenient and quiet movement.

The different mounting rings allow flexible changeover between different mounting interfaces. For all common tool holder types and sizes up to SK 50, HSK 100 and PSC 10.

Special cooling adapter

Cooling adapter for special shrink fit chuck shapes and sizes (e.g. also for D3 mm to D5 mm). Suitable for cooling bells D14 mm to D16 mm or D25 mm to D32 mm.

Storage board for mounting rings and special cooling adapters The storage board provides space for storing four mounting rings and six special cooling adapters size I or three special cooling adapters size I and size II. Tool trayFor storing socket tools at the shrinking workstation. The position of the tray can be freely selected by the operator. Shelf for cleaning brushesA shelf with all brush diameters is available for storing cleaning brushes, which can be attached to the device in any position using magnets. The brushes for cleaning the mounting hole of shrink fit chucks are also available from ZOLLER - for shaft diameters D3 mm to D32 mm, optionally made of brass or plastic. Split shielding discs with trayAn optional set of shielding discs (5 pieces) in a split design including the corresponding disc tray can be ordered for shrink-fitting offset tools.

Coil operating handle

For optimum user-friendliness, the operating handle, which is fitted on the left as standard, can be fitted on the right or on both sides. Each operating handle is equipped with two function buttons - for moving the coil and activating the heating process.

Shrinking device »toolEx«

»toolEx« helps you to remove tools from the shrink fit chuck that cannot be pulled out by hand or with pliers, such as broken tools. The set includes a holder and six ejector rods.

Length adjustment »liteSet«

Use »liteSet« to set the projection length of the tool to be shrunk. The maximum projection length is 150 mm. The set contains four clamping prisms for shank diameters D3 mm to D32 mm.

ZOLLER Basic – for compact efficiency

Name: »powerShrink«
Brand: Zoller

Storage compartment

Storage compartment for shielding system

Storage compartment for shielding system – for safe and convenient storage right on the device, as well as for quick access when changing discs.

Induction coil

Intelligent induction coil

Intelligent induction coil – with shielding discs for precise and energy-efficient shrinking. The powerful 14-kVA coil enables short processing times and ensures maximum safety in daily use. The user interface assists in selecting the correct shielding disc and authorizes the process as soon as the inserted shielding disc matches the selected tool data set.

The optional fume extraction system activates automatically during the heating process, extracts the resulting fumes, and directs them to the ZOLLER filter unit. This protects the health of employees.

Air cooling

Integrated Air Cooling

Integrated air cooling – available as an option – for simple and contactless cooling after the shrink process. Thanks to an innovative nozzle design, air consumption and noise levels are reduced to a minimum.

TFT touch monitor

TFT touch monitor with ZOLLER »pilot« software

Industrial 13.3" TFT touch monitor, with ZOLLER »pilot« software – impresses with a razor-sharp display and simple operation via touch. The clearly-structured graphic software interface intuitively guides you through the shrink process, with the help of large function areas and colors.

Linear axis

Smooth-Running Linear Axis

Smooth-running linear axis – for fast positioning of the tool holder relative to the induction coil. The clever axis clamping mechanism, the high-precision THK linear guide, and the integrated weight compensation enable ergonomic workflows and ensure a long service life. The travel distance is 400 mm.

Storage compartment

Storage compartment for reducer rings and shaft tools – for quick access right on the machine.

Storage board

Ergonomic storage board

Ergonomic storage board – for keeping cleaning brushes within easy reach, as well as promoting organization, short reach distances, and clean drill holes.

Storage compartment

Storage compartment for reducer rings and shaft tools – for quick access right on the machine.

Tool Holder

Height-Adjustable Tool Holder

Height-adjustable tool holder – with a quick-change system for holder rings and dual-sided operation for maximum ease of use. Color markings, combined with the axis scale, enable reliable positioning at the optimal cooling position after heating.

Adjustable feet

Adjustable feet – for a secure footing on the workbench.

Storage compartment for shielding system

Storage compartment for shielding system – for safe and convenient storage right on the device, as well as for quick access when changing discs.

Intelligent induction coil

Integrated Air Cooling

TFT touch monitor with ZOLLER »pilot« software

Smooth-Running Linear Axis

Storage compartment

Storage compartment for reducer rings and shaft tools – for quick access right on the machine.

Ergonomic storage board

Ergonomic storage board – for keeping cleaning brushes within easy reach, as well as promoting organization, short reach distances, and clean drill holes.

Storage compartment

Storage compartment for reducer rings and shaft tools – for quick access right on the machine.

Height-Adjustable Tool Holder

Adjustable feet

Adjustable feet – for a secure footing on the workbench.

Tool Heat Shrink Technology: Your Advantages

Read how we have achieved significant increases in energy efficiency, process speed and ergonomics. Use perfection for your production.

Learn more

Christoph Zoller — 1:1 Expert Meeting

The individual exchange about your goals and our ideas for achieving them. Online advice from ZOLLER directly from the Smart Factory. Arrange your appointment now.

Learn more

ZOLLER Basic – for compact efficiency

Storage compartment

Storage compartment for shielding system

Induction coil

Intelligent induction coil

Air cooling

Integrated Air Cooling

TFT touch monitor

TFT touch monitor with ZOLLER »pilot« software

Linear axis

Smooth-Running Linear Axis

Storage compartment

Storage compartment

Storage board

Ergonomic storage board

Storage compartment

Storage compartment

Tool Holder

Height-Adjustable Tool Holder

Adjustable feet

Adjustable feet

Storage compartment for shielding system

Intelligent induction coil

Integrated Air Cooling

TFT touch monitor with ZOLLER »pilot« software

Smooth-Running Linear Axis

Storage compartment

Ergonomic storage board

Storage compartment

Height-Adjustable Tool Holder

Adjustable feet

Tool Heat Shrink Technology: Your Advantages

1:1 Expert Meeting

Select language